Why Nanocrystalline

The Engineering Case for Liquid Magnetics Cores

Conventional magnetic core materials impose hard limits on switching frequency, operating temperature, and passive component volume. Liquid Magnetics nanocrystalline cores remove those constraints — enabling smaller, lighter, more efficient power conversion systems across defense, aerospace, and industrial applications.

Up to 60%
core loss reduction

Dramatically Lower Core Loss

At 100 kHz and above, LM-NC Series cores exhibit core loss below 8 W/kg — compared to 18–35 W/kg for MnZn ferrite under identical conditions. Lower core loss translates directly to reduced heat generation, smaller heatsinks, and higher system efficiency. At 1 MHz, the advantage widens further: LM-NC cores remain below 45 W/kg while ferrite alternatives exceed 100 W/kg.

< 8 W/kg
core loss @ 100 kHz
vs. 18–35 W/kg
MnZn ferrite equivalent
10 MHz
maximum operating frequency

High-Frequency Operation to 10 MHz

LM-HF Series ultra-thin ribbon cores (10–15 µm) maintain useful permeability and acceptable core loss up to 10 MHz — a frequency range inaccessible to conventional ferrite or amorphous alloys. This enables GaN and SiC converter designs to push switching frequencies into the multi-MHz range, dramatically reducing the required inductance and transformer size.

10 MHz
max switching frequency
3–10×
frequency advantage over ferrite
-55°C to +200°C
operating temperature range

Full Military Temperature Range

Initial permeability remains within ±5% from -55°C to +200°C — a stability envelope that no MnZn ferrite can match. Ferrite permeability can shift 20–40% across the military temperature range, forcing designers to derate heavily or add compensation circuitry. Liquid Magnetics cores eliminate that design burden, simplifying thermal management and reducing BOM complexity.

±5%
μᵢ drift across full temp range
vs. 20–40%
typical ferrite drift
500K+ hrs
demonstrated MTBF

Long-Life Reliability

Demonstrated MTBF of 512,000 hours under MIL-HDBK-217F Part Stress analysis, with a Weibull shape factor of β = 3.4 indicating wear-out dominant failure mode — not random early failures. Every core is 100% electrically screened before shipment. Qualification data is available under NDA for defense and aerospace programs requiring MIL-PRF-27 traceability.

512,000 hrs
demonstrated MTBF
< 0.2 FIT
failure rate
Size & Weight Reduction

Smaller Passives, Lighter Systems

Higher switching frequency directly reduces the required inductance for a given ripple current specification. Because inductance scales with core volume, operating at 10× higher frequency can reduce core volume by 10× or more — subject to winding and thermal constraints. For weight-critical aerospace and defense platforms, this translates to measurable system-level mass reduction.

Core volume reductionUp to 10×
at 10× frequency increase, same ripple spec
Transformer mass reduction40–70%
typical for LLC converter at 3.5 MHz vs. 350 kHz
Power density increase3–5×
W/cm³ for GaN-based converter with LM-HF cores
Heatsink volume reductionUp to 50%
from lower core loss at equivalent power throughput
System Efficiency

Where the Losses Go

In a typical 1 kW DC-DC converter operating at 500 kHz, magnetic core loss accounts for 15–25% of total converter losses. Switching to LM-NC Series cores reduces that component by up to 60%, contributing 2–4 percentage points of overall efficiency improvement. At higher frequencies the impact is even greater — at 3 MHz, core loss can dominate total loss, making core material selection the primary efficiency lever.

Reduced thermal load

Lower core loss means less heat to remove. Smaller heatsinks, reduced airflow requirements, and simplified thermal interface design.

Higher duty cycle stability

Near-zero magnetostriction eliminates acoustic noise and mechanical stress that degrades efficiency over time in high-magnetostriction materials.

Wider operating range

Flat permeability vs. temperature allows the converter to maintain efficiency across the full operating temperature range without derating.

Reduced filter complexity

Higher switching frequency reduces output ripple for a given filter inductance, allowing smaller output capacitors and simpler EMI filter design.

Application Use Cases

Where These Benefits Matter Most

Airborne Power Conversion

Defense
Challenge

MIL-STD-704F 28 VDC bus conversion to regulated 5 V / 12 V rails in a 3 ATR short chassis. Weight budget: 800 g total for the power supply assembly.

Solution

LM-NC Series cores at 2 MHz switching frequency reduce transformer mass by 55% vs. ferrite-based design at 300 kHz. Full -55°C to +85°C operation without derating. MIL-PRF-27 qualified.

Outcome

Power supply assembly mass: 620 g. Efficiency: 94.2% at full load.

Avionics DC-DC Converter

Aerospace
Challenge

DO-160G qualified isolated DC-DC converter for flight-critical avionics. 270 VDC input, 28 VDC output, 500 W. Operating altitude to 70,000 ft.

Solution

LM-NC Series cores in a phase-shifted full-bridge topology at 800 kHz. Permeability stability across -55°C to +125°C eliminates temperature compensation. Altitude qualification per DO-160G Section 4.

Outcome

Core loss: 6.2 W/kg at operating point. Efficiency: 96.1%. Zero field returns in 3 years of service.

GaN-Based Motor Drive

Industrial
Challenge

Variable frequency drive for a 75 kW industrial servo motor. Target switching frequency: 4 MHz to minimize acoustic noise and output filter size.

Solution

LM-HF Series cores (12 µm ribbon) in a common-mode choke and output filter inductor. Core loss at 4 MHz: 28 W/kg — within thermal budget. Encapsulated for IP67 environment.

Outcome

Output filter volume reduced 65% vs. 400 kHz ferrite design. Acoustic noise: < 35 dB(A) at rated load.

Quantify the Benefit for Your Application

Share your converter topology, frequency, and thermal budget. Our engineering team will provide a core loss comparison, size estimate, and material recommendation within 5 business days.

Start an Engineering Discussion →