Core Technology

Advanced Nanocrystalline Soft Magnetic Cores

Liquid Magnetics has developed a proprietary class of nanocrystalline and amorphous soft magnetic core materials engineered for high-frequency power conversion from DC to 10 MHz. Our liquid-phase processing technique enables nanometer-scale grain control — the foundation of dramatically reduced core loss, superior permeability stability, and extreme environmental resilience.

Material Science

How Liquid-Phase Processing Changes Everything

Conventional soft magnetic materials — ferrite, silicon steel, and powder cores — are constrained by grain boundary scattering, eddy current losses, and thermal instability at frequencies above 500 kHz. Liquid Magnetics' proprietary liquid-phase processing route bypasses these limitations by forming the magnetic alloy in a controlled melt state, enabling precise control of grain nucleation and growth at the nanometer scale.

The resulting nanocrystalline microstructure achieves near-zero magnetostriction and an exchange-coupled grain network that dramatically reduces both hysteresis and eddy current loss components. The material is then precision-annealed in a controlled magnetic field to set the easy-axis orientation, optimizing permeability for the target application frequency range.

This process produces cores with permeability stability within ±5% from -55°C to +200°C — a performance envelope that no conventional ferrite or amorphous alloy can match across the full military temperature range.

Fe₃Si nanocrystals in amorphous matrix — 10–15 nm grain diameter
Fe₃Si nanocrystal
Amorphous matrix
Grain boundary
Material Portfolio

Three Material Classes, One Platform

LM-NC Series
Nanocrystalline Alloy
Flagship

Fe-based nanocrystalline alloy with FINEMET-class microstructure. Optimized for high-frequency transformers and inductors from 10 kHz to 10 MHz. Lowest core loss in class at frequencies above 100 kHz.

Permeability (μᵢ)80,000 – 150,000
Saturation Flux (Bₛ)1.24 T
Core Loss @ 100 kHz< 8 W/kg
Core Loss @ 1 MHz< 45 W/kg
Coercive Force (Hc)< 0.5 A/m
Curie Temp (Tc)> 570°C
LM-AM Series
Amorphous Alloy
High Bₛ

Co-based amorphous alloy with near-zero magnetostriction. Preferred for current transformers, EMI filters, and applications requiring extremely low coercive force and high linearity.

Permeability (μᵢ)100,000 – 300,000
Saturation Flux (Bₛ)0.55 T
Core Loss @ 100 kHz< 12 W/kg
Core Loss @ 1 MHz< 80 W/kg
Coercive Force (Hc)< 0.1 A/m
Curie Temp (Tc)> 250°C
LM-HF Series
High-Frequency Nanocrystalline
MHz Range

Ultra-thin ribbon nanocrystalline alloy optimized for operation above 1 MHz. Ribbon thickness reduced to 10–15 µm to minimize eddy current losses at multi-MHz frequencies. Targeted at GaN/SiC converter designs.

Permeability (μᵢ)10,000 – 30,000
Saturation Flux (Bₛ)1.20 T
Core Loss @ 1 MHz< 22 W/kg
Core Loss @ 5 MHz< 110 W/kg
Ribbon Thickness10 – 15 µm
Max Frequency10 MHz
Manufacturing Process

Precision from Melt to Core

01

Alloy Formulation

Precise elemental blending of Fe, Si, B, Nb, and Cu in controlled ratios. Alloy composition is the primary lever for setting target permeability, Bₛ, and Tc.

02

Liquid-Phase Casting

Melt-spinning at controlled quench rates produces amorphous ribbon at 10–25 µm thickness. Quench rate determines the degree of structural disorder and sets the baseline for subsequent crystallization.

03

Nanocrystallization Anneal

Controlled annealing at 500–560°C nucleates Fe₃Si nanocrystals (10–15 nm diameter) within the amorphous matrix. Crystal volume fraction and size distribution are the key parameters governing final magnetic properties.

04

Field Anneal

Secondary anneal in a transverse or longitudinal magnetic field sets the induced anisotropy direction, optimizing the B-H loop shape for the target application — flat loop for inductors, square loop for flux gate sensors.

05

Core Winding & Encapsulation

Ribbon is precision-wound to target geometry (toroid, C-core, E-core, custom) and encapsulated in epoxy or housed in a protective case. Gap insertion available for DC-bias applications.

06

100% Electrical Test

Every core is tested for initial permeability, core loss, and impedance at specified frequency. Traceability records maintained per AS9100D and MIL-PRF-27 requirements.

Competitive Analysis

LM-NC vs. Competing Core Materials

ParameterLM-NC SeriesMnZn FerriteAmorphous (Fe-based)Powder Core (MPP)
Core Loss (W/kg)< 818 – 3512 – 2040 – 120
Max Frequency10 MHz3 MHz500 kHz300 kHz
Saturation Flux (T)1.240.451.560.75
Temp Stability (±%)< 5%20 – 40%8 – 15%5 – 10%
Temp Range (°C)-55 to +200-40 to +125-55 to +150-55 to +200
Magnetostriction≈ 0LowHighMedium

* Data at 100 kHz, 0.1 T, 25°C. Competitor data from published datasheets.

Application Areas

Designed for Demanding Environments

Defense Power Conversion

DC-DC converters, inverters, and power conditioning units for airborne, shipboard, and ground vehicle platforms. Qualified to MIL-STD-461, MIL-STD-810, and MIL-PRF-27.

Aerospace Avionics

Transformer and inductor cores for DO-160 qualified power supplies, ARINC 429 bus interfaces, and flight-critical power management systems.

GaN/SiC Power Electronics

High-frequency magnetics for next-generation wide-bandgap converter designs operating at 1–10 MHz switching frequencies. Enables significant reduction in passive component volume.

Industrial Motor Drives

EMI filter inductors, common-mode chokes, and DC link inductors for variable frequency drives and servo amplifiers operating in harsh industrial environments.

Medical Power Systems

Isolation transformers and filter inductors for IEC 60601-1 compliant medical power supplies requiring low acoustic noise and high reliability.

EV Charging Infrastructure

Onboard charger (OBC) and DC fast charger magnetics requiring high power density, wide temperature operation, and long service life.

Request a Technical Data Package

Full material characterization data, Steinmetz parameters, impedance vs. frequency curves, and application notes are available under NDA to qualified engineering teams.

Contact Engineering →